Description:
An ACDelco GM Original Equipment Engine Water Pump circulates coolant through your vehicle's radiator and engine system to help maintain proper engine temperature and performance. This original equipment water pump has been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors. WARNING: Cancer and Reproductive Harm - https://www.P65Warnings.ca.gov
Get the GM quality you know and trust with ACDelco's GM Original Equipment Water Pumps line. Stay with the brand of parts your General Motors vehicle came with and get peace of mind that the fit, form, and function is up to the high standards and specifications of General Motors. Built to meet the latest manufacturer-specified designs, components in ACDelco's Water Pumps line include water pumps, kits, gaskets, seals, and O-rings. ACDelco GM Original Equipment Water Pumps components are manufactured for virtually every model of GM car, light duty truck, and sport utility vehicle. When it comes to protecting the life of your engine, ACDelco Professional Water Pumps offer the heat control you need to keep things cool.
Features and Benefits:
- Coated seals with a stainless steel spring for durability
- GM-recommended replacement part for your GM vehicle's original factory water pump
- Heat-treated impeller shafts supported by high-quality ball/roller bearings for smooth, reliable operation in virtually all conditions
- Manufactured to GM OE specification for fit, form, and function
- Offering the quality, reliability, and durability of GM OE
- Thoroughly tested for reliable, leak-free performance
- Uniform wall sections and smooth coolant-flow cavities for efficient operation
- Tips for Water Pump Inspection:
- – A stain around the weep hole is acceptable. However, if a weep occurs with the engine running and the coolant system pressurized, then the water pump should be replaced.
- – Clean all excess dirt and debris from the water pump housing.
- – Inspect for leakage at the water pump outlet housing or the rear cover gasket, and leakage at the water pump vent or weep hole.
- – Run your vehicle to increase engine temperature, and ensure the system is pressurized.
- Tips for Water Pump Servicing & Installation:
- – After installation, pressure-test the system for leaks and check for sufficient fan blade clearance between the blade and radiator shroud.
- – Clean all sealing surfaces, and make sure all old gasket material is removed before installing your replacement component.
- – Clean and reinstall the coolant recovery reservoir before flushing the cooling system.
- – Do not use any non-approved flush agents, and replace the coolant according to manufacturer's specifications.
- – Flush the cooling system completely, using power flush equipment or thermal cycling the system with clean water three times. The most effective method of system flushing is to use a coolant exchanger, following the manufacturer's operating instructions.
- – Inspect related components in the cooling system, including your fan blades, fan clutch, engine mounts, radiator, belts and hoses, and reservoir.
- – Never strike the water pump shaft, since this will damage the new water pump.
- – Torque all bolts according to the manufacturer's specifications, and adjust belts to proper tension (if applicable) to manufacturer's specifications.
- – Use sealant tabs only if recommended. Some sealant tabs or similar compounds may restrict coolant flow through the passages of some cooling systems.
- – With the new pump installed, turn the hub by hand and check for rotation.
- Tips to Help Prevent Water Pump Failure:
- – Ensure that your engine fan pulley (or clutch, if used) is seated properly on the pump's shaft. If the fan wobbles during rotation, vibration resulting in premature bearing wear may occur. Also check the fan clutch for wear and replace as necessary.
- – Flush your cooling system whenever the water pump or other system components are replaced. This will help prevent contamination from entering the system, which may result in repeated failure.
- – Inspect the fan blade. If damage is not detected, bent blades, loose rivets, and cracks may result in premature bearing failure. If damage is found, do not try to repair the fan-the part should be replaced.
- – Inspect the thermostat and radiator cap. Examine your thermostat and radiator cap, and replace if they show signs of sticking or leaking.
- – Never overtighten your drive belts. Belts that are too tight may cause an overload on pump bearings, greatly reducing the life of the water pump.
- – Utilize quality coolant when refilling your cooling system with the recommended 50/50 coolant/water mix. Distilled water should be used, as hard tap water can leave mineral deposits in the cooling system and reduce coolant flow, or result in corrosion and seal damage. Contaminated or depleted coolant can also result in corrosion and seal damage, and lead to pump failure. Take care to select the correct coolant for your vehicle by consulting the vehicle manufacturer's service information.
Specifications:
Housing Material:
Aluminum
Impeller Rotation:
STANDARD
Impeller Vane Quantity:
7
Informational Chart 1:
PL25_PL26_IC_WaterPumpComposition.jpg
Informational Chart 2:
PL25_PL26_IC_CoolingSystemOperation.jpg
Mounting Hardware Included:
No
Mounting Hole Quantity:
7
Thermostat And Housing Included:
No
Manufacturer Warranty:
24 Month / Unlimited Mile Limited Warranty (Parts Only). Please see ACDelco.com for more details.
