Description:
CARDONE Remanufactured Vacuum Brake Boosters, Hydro-Vac Boosters, and Hydraulic Boosters, offer your vehicle reliable stopping performance, every time. Each unit is reverse engineered, based off 40 years of CARDONE Engineering expertise, where original design weaknesses are identified, corrected and where applicable upgraded to provide a more durable part then the original unit. Every unit is remanufactured to meet or exceed OEM performance, providing a quality product both you and your vehicle rely on.
Features and Benefits:
- 100% O.E. quality seals, and check valves are installed on every unit for like-new performance and reliability.
- 100% O.E. quality seals, diaphragms and check valves are installed on every unit for like-new performance and reliability.
- All units are 100% tested to ensure reliable performance.
- Exclusive rust-prohibitive finishing process extends unit life.
- Guaranteed fit and function.
- Master cylinder output rods are pre-adjusted (when included) for easier and faster installation.
- Master cylinder output rods are pre-adjusted (when included) for quick and easy installation.
- Meets or exceeds O.E. performance.
- New mounting nuts and washers ensure proper, hassle-free installation.
- Remanufactured to match O.E. performance.
Specifications:
Brake Pedal Rod Extension Included:
No
Brake Service Grade:
Regular
Contains Electronic Components:
No
Diaphragm Diameter:
10.38 in.
Diaphragm Diameter:
263.65 mm
FAA_A10:
The most common way to identify the brake booster is by the vehicle application. However, most brake boosters have a pedal rod identification number stamped on the end of the rod. This can helpful in identifying the correct replacement brake booster.
FAA_A1:
A brake booster assists in pushing the master cylinder piston when the brakes are applied. This multiplies pedal force to decrease stopping distances.
FAA_A2:
For proper functionality, a brake booster will need a consistent supply of 18-21 inches of vacuum.
FAA_A3:
With the engine off, pump the brake pedal until it feels firm and hold. Then, start the engine and the pedal will sink slightly if the booster is operating properly.
FAA_A4:
Fuel and oil vapors can enter the vehicles PCV system. These vapors will prematurely deteriorate the brake boosters internal diaphragm.
FAA_A5:
After replacing a brake booster, it may be necessary to adjust the brake light switch. Some vehicles contain a one-time use brake light switch. In these cases, the brake light switch will need to be replaced.
FAA_A6:
No, brake boosters are application specific. Most will have different master cylinder and firewall mounting spreads.
FAA_A7:
Brake pedal free play is a measurement of how far the brake pedal moves before the master cylinder first begins engagement. Some vehicles will require an adjustment. Please refer to your vehicles service manual.
FAA_A8:
This is due to a failing master cylinder piston seal. This will result in brake fluid entering and contaminating the brake booster. The master cylinder and brake booster will need to be replaced.
FAA_A9:
A common cause is a restricted vacuum hose. If the vacuum line is free flowing, there could be more extensive engine damage or wear. Engine vacuum also fluctuates based on altitude. Please refer to the O.E. specification for your vehicle.
Gasket Or Seal Included:
No
Housing Diameter:
10.565 in.
Housing Diameter:
268.35 mm
Is Or Contains A Battery:
No
Is Or Contains A Bulb:
No
Is Prop Sixty Five Affected:
No
Is the item CARB affected:
No
Master Cylinder Included:
No
Master Cylinder Stud Thread Size:
M10x1.5
Mounting Bracket Included:
No
Mounting Hardware Included:
No
Package Contents:
Booster; Instruction Sheet
Product Condition:
Remanufactured
Stud Thread Size:
M10x1.5
General Motors #:
21010181
Manufacturer Warranty:
12 Months
