Description:
Expertly remanufactured to rigorous quality and performance standards, all CARDONE Brake Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. These remanufactured brake calipers are 100% pressure-tested to deliver consistent, industry-leading brake performance. Each unit arrive s with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.
Features and Benefits:
- A plastic cap plug protects every brake port thread to ensure trouble-free installation.
- As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
- Calipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
- Mounting bracket is included where applicable for a hassle-free installation.
- New banjo bolts are included where applicable to ensure a perfect fit and quick installation.
- New bleeder screws provide trouble-free bleeding and a positive seal.
- New stainless steel hardware clips and new mounting pins are included where applicable.
- New washers are included where applicable for a proper seal.
- Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
- Pistons are durable, resistant to cracking or pitting and handle great loads.
- Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
Specifications:
Abutment Clips Included:
Yes
Anti-Rattle Spring Included:
No
Bleeder Screw Cap Included:
No
Bleeder Screw Included:
Yes
Bleeder Screw Quantity:
1
Bleeder Thread Size:
M10x1.0
Caliper Casting Material:
Cast Iron
Caliper Finish:
Oil Emulsion
Caliper Slides Included:
Yes
Casting Number:
13716801 RIGHT
Casting Number:
TRW 134248
Contains Electronic Components:
No
FAA_A1:
Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturers recommendations.
FAA_A2:
As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
FAA_A3:
Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
FAA_A4:
Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
FAA_A5:
A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
FAA_A6:
A silicone grease is used on floating caliper mounting pins.
FAA_A7:
New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
Inlet Fitting Type:
Banjo
Inlet Port Size:
0.394 in.
Inlet Port Size:
10.00366 mm
Inlet Thread Size:
M10x1.0
Is Or Contains A Battery:
No
Is Or Contains A Bulb:
No
Is Prop Sixty Five Affected:
No
Is the item CARB affected:
No
Mounting Bolt Included:
No
Mounting Bracket Included:
Yes
Mounting Hardware Included:
Yes
Mounting Hole Diameter:
0.63 in.
Mounting Hole Diameter:
15.9957 mm
Mounting Hole Thread Diameter:
0.63 in.
Mounting Hole Thread Diameter:
15.9957 mm
Mounting Hole Thread size:
M16x2.0
Package Contents:
Caliper; Instruction Sheet; Bracket; Hardware Kit
Pad Wear Sensor Included:
No
Piston Diameter:
2.206 in.
Piston Diameter:
56.0324 mm
Piston Material:
Phenolic
Product Condition:
Remanufactured
Rust Resistant Coating:
Yes
Manufacturer Warranty:
24 Months
